M1152

Nicely done!

From the Netflix website. Netflix will work on Internet connection speeds of 0.5 megabits per second (Mbps), but we recommend 1.5 Mbps or higher for the best experience. In the link above you see Netflix has a bandwidth settings so you would adjust your bandwidth accordingly. We have been using Netflix for years and have seen some peering issues in the past. Since they both have free trails give one a try one month then the other the following month and see which service streams best for you. It could be one service will stream in HD and the other will not because of the DSL limitations or because of possible peering issues with your ISP. Keep in mind if the DSL is a slower tier like 1.5Mbps or lower it may stream great to one device but if you then try to stream to a second device for your kids or whatever it could be too much for your DSL service. As far as the original post we hadn’t tried Amazon yet but intend too

Well said Howard and it’s not over yet! For the pessimist that thinks it is over for us go fourth and multiply. Keep those faxes, social media, emails and calls going. You could bet it will be rammed thru on party lines and if the Gov sees no resistance from us then he should side with the Dems and sign it into law. So for the rest of you save the CC Rino shit and get your azz in gear and spend a little less time on the forum with the naysayer postings because honestly it’s pathetic. So get off your azz and make your protest known. Again, very nice job Howard!

Get him a Gift Certificate at OpticsPlanet, so he could either go with what you give him or could kick-in the rest.....

Are you getting kicked off Wired, Wi-Fi or both? Are you dropping your internet connection for ALL your devices and have you ruled out the modem? FWIW my router is over 3 years old and works great but then again I re-flashed my router with dd-wrt.

You could try disabling it in the Device Manager but if the user has Admin rights they could re-enable it. I would probably just disable in the Bios and password protect the bios settings

I’m in the over 50 club and I have the XS Sight Systems Tritium AK-47 Sight with the Krebs Krebs Custom Ghost Ring Sight. One of the other long time forum members recommended the Ghost Ring a year or two back but I still needed help up front so I added the XS Tritium. Is this the best setup, no but better than it was IMO.

I’m looking to do a Varmint rifle. I was going to go with Model “1” Sales to get the complete kit but seen a few bad reviews. What do you guys think? Kind of jumping around of this but here’s was what I have it narrowed down to so far, I’m leaning toward the first one from WW. Windham Weaponry Varmint Exterminator @ $697.50 (unadvertised TAX special) Stag Arms Super Varminter Model 1 Sales Any thoughts or suggestions? Thanks in advance

already posted here

Sure, hope it works out for you and hopefully the web form expedites the process for the state roads. Either way should be an interesting motorcycle season

done

Report them, if we don’t let them know they won’t fix them. Here’s a link to NJDOT Pothole Repair with the County Pothole Hotline

just wondering, is there a way the moderator's could send an email blast to ALL member's with this instruction, or would that be asking too much?

excellent point & done

and BTW it’s a nice looking rifle to boot

Not just this thread but it became obvious last summer from several other post on these boards some folks have already thrown in the towel. If you haven’t surrendered good for you. If you want to hang this mess on voting why do you think these A-holes keep getting voted back in? That’s easy NJ has high number of state, county and local government workers who have been brainwashed into voting for the Dems. In addition to those groups you could add teachers, cops, fireman and probably any other unionized labor. NJ Dems also play the redistribution of wealth game like their Washington counterparts so that works for them as well. The Dems have targeted guns because it sounds great to the uninformed voter. NJ Dems currently in power aren’t capable of producing any legislation that would actually benefit the NJ economy so that is why they do this. Current NJ Dems entire mission in life is to get elected, gain power and get re-elected. End of Story

Jeez, I’d hate NJGF members already surrendering to this and throwing in the towel without even a fight. I’m sure it’s been referenced on the forum already but you need to look at the bill. I seen the link to the bill in the comments section of nj.com and those folks seem to be putting up more resistance than our fellow forum members and good for them. Anyhow if you are ready for 10 rounds you might want to plan for 5 rounds. As posted in the comment section of nj.com it says “it proposes limiting magazine capacity to FIVE” and he goes on to say look at page 6 lines 10 & 11 and the last two lines of the last page. Here’s the bill one more time and it looks like 5rds to me.

you don't need a drill press, buy the kit from css and your good with just a cordless

I've used AAA three times now without any issues. Maybe not the best price but they show up on time and do it right.

What are your thoughts on the the SGM Bolt-on Muzzle Brake for the Saiga 308, Yea or Nay for NJ? see links below http://www.carolinashooterssupply.com/product_p/sgm-308-brake.htm or https://www.sportsmentacticalsupply.com/product/49-0310/308-Rifle-Muzzle-Brake---Target-for-Saiga-by-SGM-Tactical/

The Moderator here mentioned the Geissele when I picked up my first AR platform rifle which was the M&P15. The S&W trigger was horrible so the Geissele was the perfect upgrade. And just like Blake said in post #2 stated I now own two of Geisseles. Lastly its nice to know they are made PA.

Off topic but please keep us posted if you go thru on this. I’ve been very interested in the 5.45x39 round and was thinking about an 5.45 upper as well however someone posted here (NJGF) there are feeding issues with the tapered x39’s. Plus the fact that we are capped at 15 rds, what impact will that have loading mags? Has anyone got 15rds in a NJ neutered mag and will it feed correctly?

I thought about it, occasionally I would buy ammo from Cope’s and noticed that they sell Wise, I’d thought about trying it but never got around to testing it. If you do sell them are you going to sell the stoves too? 25 year shelf life, I'd have to will it to someone LOL. Anyhow I’ll follow the thread and see what kind of pricing you get but as mentioned above I should probably test it first…

Good question, I never heard of them...Probably some libs doing data mining No flack, just my opinion. I agree with the other post, we would be lucky to be presented with that option but here’s the deal. The State of NJ would turn the entire process it into one huge cluster-f*** of paper work and red tape. That’s their MO and they just can’t help themselves form not doing it. Furthermore I have ccw permits for five other states so should I or anyone else with valid ccw permits be forced to undergo more training, I think not