FishHunter

If you can find Bullseye, grab all you can. One of the most consistent powders, especially in Minor loads for 40S&W. Current formula is clean burning. Probably the best over all powder unless you go for Max loads for compensated guns.

I run both Major and Minor with TG and Extreme 180gr plated FN. - very clean and more accurate then I am. My top choice is Bullseye but TG is good and I got my hands on a bunch of it

As stated, for one caliber, it is not necessary to use a powder through expander. I use them, but I run 4 calibers. If you are using lead or plated bullets, find an expander that is a bit larger then your bullet diameter. For 9mm [355-356] I use a 357 expander. I find it also helps to polish[not grind] the cone section to a smooth mirror surface - helps with releasing the case on the down stroke. For jacketed bullets, the standard size will do. Make sure you do not over flare the mouth - kills brass life.

I am I the freehold area. Let me know what you plan to reload. I'll be glad to show you the ropes. I load 9mm, 40 and 45. Rifle is a whole other animal.

The electronic ear muffs are a good deal $55 after discounts and free shipping. These have a noise reduction rating of 27db, not like the Cabelas muffs which have a 22db rating.

These muffs have a reduction rating of 22db. even the cheap foam plugs from Depot have a 28db rating.

There is a limit of 1 brick - not worth the gas money to drive out.

Energy calc uses V squared, small increase in V makes greater calc factor than small mass diff. At same velocity, heavier bullet has more emergy

W231 at solomon's. 1lb limit. Bullseye is my fav. But have not seen it anywhere. Titegroup shows up periodically. Got a bunch from Cabelas but have to ship to ny.

Academy has free shipping on orders of $39 or more. I grabbed a case of 12ga and 20ga target loads for 54.99 and 59.99 each case [shipped to NJ]. Also took a couple of small packs of 22lr [they have limits].

NJ DA will make your life into a nightmare if the newspapers report a shooting with "bladed" bullets. Safest and easiest ammo for in-home defense is shotshel or frangible bullets. Anything else will travel through walls and possibly hurt the people you are protecting. Think home defense, not home based slaughter of intruders.

Shotgun ammo at freehold dicks is buy one get second at 50%off. Got a case of 20ga federal target for 56 including tax (0.224 per she'll) Slugs not on sale.

I went to CMO yesterday, looking to pick up a used 20ga for my daughter. They did not have what I wanted but they do have a number of nice used shot guns. Mostly in 12ga but that is true for most stores. Unlike previous visits, the counter guys were actually friendly and helpful - pleasent surprise.

I would buy as much Bullseye as possible. The powder has one of the most consistent burn rates at low volume. It meters exceptionally well. There is a popular myth that Bullseye is dirty but that stems from a decades old formula. I've loaded 9mm, 40sw and 45acp with Bullseye, titegroup, W231 and sr7625. For smallest deviation at minor PF loads, Bullseye has served me very well. Other powders look like they are cleaner but in reality you notice unburned grains flying out of the barrel. Have experimented with Unique, very good overall but I had to check load weight more frequently. It just did not meter as consistently for me through a Hornady Powder measure.

Heavier bullets are longer than lighter heads of the same caliber. Once they are spining out of the barrel, they have more stability due to more weight in the tail. Lighter bullets will shoot flatter at the same speed but will be influenced by other factors, more that heavier projectiles. Open 9mm uses light bullets at 1400 FPS or more to get a very flat trajectory

Loading soft for idpa or minor PF makes a chrono a requirement. Going too slow will mess up accuracy and possibly your gun - if you squib a round

The stock Ruger extractor sometimes has imperfections at the edge. I usually stone the lower edge just to take the burr off. If you want to eliminate the magazine interlock, do not buy any parts. You can grind off a tab on the OEM interlock and it lets you drop the hammer without the mag - free. If the bolt face is not too fouled, you should not have any problems. Also check the bolt travel [without the spring]. It should slide out by itself if you tip the gun to the ceiling. Sometimes there is considerable friction from rough edges on the bolt and its housing. buff these smooth to ensure good performance with the weakest ammo.

95% of the time, residue buildup causes the symptoms you describe - especially if you apply oil type lubricants on the bolt. The oil keeps the considerable gunk from 22's from falling away. Clean the bolt face with a brush and pick and do not use oil on the surface.

I have 1 can of H110 that I would let go. Would prefer to trade.

MidwayUsa, Cabelas, Natchezz, etc. all ship to NJ and none require FID to purchase ammo. Gander will not ship ammo to NJ. All out of state firearms purchase require shipping to ffl dealer. You will need to provide the dealer's license, not your friend's. He should ask the PD in his town to explain the process. If he finds a private nj seller, they just fill out the permit and he provides his FID and license as proof. If your friend is too paranoid to provide his id for a gun purchase, perhaps he should not buy one.

Even with hazmat, still a good deal. $25/1000 for small pistol.

Midway is running a sale on CCI primers. Even with hazmat it is a good buy.

I noticed that extreme raises their prices when offering free shipping - not a bargain.

I run 147gr 9mm and 180gr 40. both plated. Lt me know what you can do. For use in uspsa and idpa, need to be accurate..

1k would do it