FishHunter

Heck cabelas's They had Autocomp today. I purchased TiteGroup myself. You have to call the reps because the webpage is not always accurate. That is how I got TG.

I love my BM Lite but the factory is known for releasing sporadic lemons. If you can not get a single clip without problems, I'd get a replacement. You did not buy a new gun to Try and make it work with factory ammo. My pistol eats Golden Bullet and standard velocity without problem. It is a competition gun so it has to run right. Check the flat head screw on top of the slide & frame. If either is not completely seated, you will have problems. The BM is very sensitive to slide fit and alignment.

Just scored some TiteGroup. Call customer service because it is not coming up on the site. They had W231 but I was a few minutes late for that. $20 hazmat fee and they will not ship powder into NJ. I had my order shipped to NY. You could always order and pick up at the store.

Thanks

I am looking for small pistol primers in NJ to avoid the hazmat charge. Does anyone sell primers in NJ?

I've spoken to a couple of people who are into cowboy action and they use TiteWad - supposedly it can be a soft shooter in a 45.

Thank you Maksim. One day I hope to go shoot at CJ, perhaps I will run into you there.

Thanks to all who offered to assist. Made plans to meet up with Grumpy at the next match. Thanks again.

20-30 would be nice

I am near Freehold but I drive the TPK every day to NYC.

Looking for small qty of 185gr 40 cal plated to test I have 200gr extreme if you want to swap

Anyone know of a dealer who would accept a 9mm with 18rd mags and pin them to 15rds for NJ compliance?

You may want to contact local gun club and ask about their youth programs. My club OBRPC has a youth small bore rifle league. They will let you use the rifle, teach proper handling and it will cost less then $10. If she likes it and sticks with it, there is scholarship money to be found in shooting sports.

Finally mounted the press and installed the dies. Have not run any powder through it yet. Just tweaking the dies. Got my hands on a few pounds of Bullseye and a SR 7625 [thanks to a fellow OBRPC member]. Set the powder through expander to barely flare the mouth, to minimize stress on the brass. Should also minimize crimp requirements. I got the seating die set up with barely any crimp - seems to hold well. Funnel on case feeder is cracked - Hornady is replacing without question. Will start with 9mm, Xtreme 147gr plated. Hand feed cases and heads until I confirm consistent results. If someone has a a Chrono, I would appreciate using it to confirm my work.

Guys, I got 2 PACKS. Once you place your order for 1 box, clear your browser cache. Go back to the site and order another box, repeat. I would have gotten more, but they sold out. Called Cabelas customer service and asked them to consolidate orders and use the $5 flat rate shipping. They did it and thanked me for the business.

FEDERAL FRESH FIRE 325RD 22LR 22LR 36GR 325CAN @ $18.99 each up right now on cabelas

I was initially considering just the loading data, should have considered the finer technical points of the process. Will look to get my hands on a practical instructional type book. Thanks.

100rd boxes in stock at dicks in E.Brunswick. Limit 3 boxes. $10/box

If reloading strictly 9mm, 40sw and 45acp, plated bullets - is a full reloading manual really necessary? Is the data from the powder and bullet mfrs not enough?

I shoot 9 and 40 and 45. Drop me a line if you want to get rid of one of the unsorted bags (20-30#). I do not mind sorting it, have to check the cases anyway. Not big bucks but better than getting cheated by the scrap stealers.

No grudges here. If it wasn't for you guys running these events, a lot of people would be stuck in a dark pen, shooting at a circle, (no rapid fire allowed)

I was relying on the OBRPC page. The weather was perfect though. Shame to have wasted it in light of our current temps.

The event was still on the OBRPC website. Showed up to find it was cancelled. Several others arrived as well. Very un-cool. Same thing on Sunday, for the IDPA. Would be nice if the event is removed from the club events calendar.

I do not have an M&P but the same troubleshooting steps should apply. 1: inspect striker and ensure that there are no burrs, chips, etc on the outer edges which may restrict full travel. 2: clean off all lubrication from striker and ensure that new lube is thin. 3: check for obstructions or poor fit of slide to frame. Ir may be that the slide is not locking fully because of some obstruction or friction with the frame. You may have had light strikes on all rounds but only 9 failed to ignite. Your weak ejection may indicate that the slide is not achieving full lockup. Not familiar with Unique so I assume this is a tested load which should work. 4: check your recoil spring, it may be defective or broken, either would produce your symptoms. 5: check that the barrel and slide are in full lockup, without a round in the chamber and then, with a round in the chamber.

I should have included that we are not in the same state. Local trades are easy, just meet at an ffl location/store and get the deal done. What do you do if the other person is 300 miles away? Sending my gun to his FFL sounds ok but his FFL is not going to make sure that I get the gun in NJ.