Everything posted by Pizza Bob
-
Tire pressure monitor systems
If they are BMW sensors going on a BMW, the chances are they are compatible. They have to be reflashed to transmit to the body computer. My dealer (domestic) does this for free. There may also be a procedure outlined in your owner's manual that tells you how to do it manually. On my car it involves some sort of initiating procedure (forget what that is) then starting at the LF and deflating the tire by 8-10 lbs until the ECU recognizes it, then reinflate. Proceed clockwise around the car. Check your owners manual. The less intricate systems use the ABS sensors to measure wheel revolutions - this type of system will only have a low pressure warning light and can't indicate which tire is low. The more complex systems have a transmitter married to a pressure transducer integral with the valve stem. This system indicates the actual tire pressure in each tire. TPMS's came about because of the lawsuit against Firestone tires that involved the rollover accidents of Ford Explorers. The result was the passage of the TREAD act, which included mandatory TPMS systems in all cars from 2009 on. Adios, Pizza Bob
-
Ammo recommendations?
Found this on the Firearm Blog this AM. Found the ammo on Gun Bot for $339/case (1K rounds). http://www.thefirearmblog.com/blog/2013/12/04/wolf-gold-223-ammo-review/
-
Recommend a revolver.
http://njgunforums.com/forum/index.php/topic/62895-what-another-revolver/ Hey Alec: Nyaa, nyaa
-
Loading 147 GR for bowling pins
You need a .45 ACP If this is a standard BP format, which is a 4' deep table with the pins set 12" from the front edge, that means you have to move them 36" rearward to knock them off the table. Even with a .45 a flatnose or hollowpoint works best - round nose bullets deflect more easily - bowling pins are hard. Good luck. Adios, Pizza Bob
-
Will be my first revolver
In the first paragraph, isn't that essentially what I said? And I have never seen or heard of a S&W frame failing because they use a side plate. The cylinder is indeed surrounded by a continuous frame. If the gun fails catastrophically, it will be cylinder and the top strap that blow out. As for the Border Patrol testing - that's kind of an apples to oranges comparison. The model 19/66 is considerably smaller than the Security Six. Apparently this was either before, or just as, Smith introduced the L-frame - a fairer comparison, size-wise, to the Security six or today's GP100. Pretty much every revolver person is aware of the problems and limitations of the K-frame with a steady diet of magnum ammo. They are a result of the physical constraints caused by the size of the gun and the main reason the L-frame exists. That being said - and keeping it Border Patrol relevant, there is no doubt the Bill Jordan would (and did) choose the K-frame guns to bet his life on and the title of his book, No Second Place Winner, says it all. We're not really disagreeing, we both stated the same conclusion, you can't go wrong with either. Adios, Pizza Bob
-
Christmas Present
Actually I was thinking about taking up ICORE to more fully utilize the new toy.
-
Will be my first revolver
The Ruger is fine for games with a 4" barrel or less - you just don't see many people using them. Probably a reason for that. While GRIZ & I agree on most things revolver, let me just say that if he means "robust" as in larger, then he is correct. If he means "robust" as stronger, then I'd have to disagree. Many people look at Ruger products and because of the thickness of the frame elements - the top strap for example - think that they must be stronger than similar sized S&W's. There is an inherent difference between the two. The Ruger is larger because it needs to be, to be as strong as the Smith. Rugers are investment cast - a very good, very precise form of casting (also known as the "lost wax" process) that requires little finish maching - but it is cast. The S&W frame is forged. Casting can result in greater frame porosity and even the possibility of voids (would hope their QC has some method to detect these). Forging does not fall prey to these same foibles. A forged piece of a smaller dimension can be stronger than a cast piece of a larger dimension. Not a slam on Ruger - they build a fine product at an excellent price, and can do so because of their manufacturing methods. I just think it's important to understand the differences. Whether that has an impact on your decision or not, is up to you - but I wouldn't assume the Ruger is more "robust". Just to muddy the waters a bit - I own both Ruger's and Smith's - although a few more of the latter than the former. Adios, Pizza Bob
-
Christmas Present
It's away visiting our friend in PA to have a FO front sight installed. Sorry.
-
Christmas Present
I guess now that Thanksgiving is behind us, we can talk about Christmas. My son just called me and told me he's buying a Beretta Compact PX4 in 9mm for his fiancé. Pretty cool. Adios, Pizza Bob
-
Will be my first revolver
While it's important for a gun to feel good in your hand, it shouldn't be your sole criteria for buying one over another. I have a few revolvers, and the first thing I do is change out the grips - the true interface between the shooter & the gun and the one with the largest influence on how a gun "feels" in your hand. There are few stock grips that I truly like - I will admit that the stock grips that feel really good to me are the Ruger rubber & wood ones, but even those were improved upon by a good set of Hogue's (my favorites). If you are leaning toward the 686 and you have any inkling of shooting it competitively, down the road, be aware that a 4" 6-shot gun (not the 686+) gives you the most versatility as far as games are concerned. Good luck with whichever you choose - but choose it for all the right reasons. Adios, Pizza Bob
-
Is Auto the same as ACP
Yes, you don't run across them often, but I know people who have purchased both, accidently, when they wanted ACP.
-
Is Auto the same as ACP
You also do not want: .45 GAP or .45 Auto Rim (AR)
-
Another is this legal in NJ question
No they wouldn't. The ATF has no standing to rule on a state law and there is no federal law that applies in this case. They would not involve themselves in a case based on a state law. I am unaware of the "AK case." To be technical, they do not slide inside one another. LOP is adjusted by a screw mechanism. Many firearms manufacturers have offered the PRS as OE on their guns sold in NJ - Sig with their original DMR model for one. While it may be prudent to err on the side of caution, NJ-ites tend to overthink things - often to their detriment. Adios, Pizza Bob
-
Another is this legal in NJ question
The response from the ATF is moot. There currently is no federal law regulating stock types, so their definition carries no weight of law in NJ. The NJ law clearly stipulates folding or telescoping neither of which applies to the PRS. Perfectly legal. As an aside - there was a case in South Jersey, and although it was not precedent setting, the argument was successfully made that the M4 stock was adjustable, not telescoping and the person beat that count. The PRS, by any stretch, is a perfectly legal stock. Adios, Pizza Bob IANAL
-
Revolver Roll Call
No, we just don't have lives.
-
Anybody Interested in a S&W Model 28-2 (.357 Mag) 4"?
6.5" model 25-2 barrel on a 625 frame - Frankengun
-
Anybody Interested in a S&W Model 28-2 (.357 Mag) 4"?
You do know that you are supposed to hold it by the end with the wooden handles, don't you? There is no gun in this world quite like an N-Frame - I love them all.
-
USPSA @ OBRPC 11/24/13
No match announcement yet, but there should be a USPSA match at Shongum (Hackettstown) on Saturday 12/7. Ron usually sends out the notice for pre-registration about a week in advance. Decent match for beginners and experienced alike. 5 stages with some run & gun, usually one standard and some steel. Good crowd. Adios, Pizza Bob
-
USPSA @ OBRPC 11/24/13
Yes, they do, but don't let that scare you off. You have to understand that 2Alpha is a top tier shooter and often wins these local club shoots and is competitive in the larger sanctioned matches. The competition is structured so that you compete against those of a skill level similar to yours. As a beginner, you go at your own pace. Strive for smoothness and accuracy and speed will come (at least that's what they tell me - couldn't prove it by the way I shoot). Read the stickys. Just be safe and have fun. Adios, Pizza Bob
-
Anybody Interested in a S&W Model 28-2 (.357 Mag) 4"?
Yes - and now there's another one
-
Anybody Interested in a S&W Model 28-2 (.357 Mag) 4"?
I found a hell of a deal on another forum and I'm surprised nobody has snatched it up. PM me for details. I have no affiliation with the seller - just hate to see a great deal on a S&W not taken advantage of. Adios, Pizza Bob
-
CALIFORNIA APPROVES SALE OF SMART GUN / Modern Arms
Sadly true
-
CALIFORNIA APPROVES SALE OF SMART GUN / Modern Arms
I agree, but having the law already on the books is like living under the sword of Damocles. There is very little in the way of definitive criteria - just that it be available for public sale. I see that Armatrix has announced pricing (ridiculous in the scheme of things), but that means that if/when it actually becomes available we are at the mercy of the state AG. Yes, I realize that it would most likely be overturned in the courts, but how long will that take and will handgun sales be suspended in the interim? I would rather it not come to that. I remember a modification made to the leaf-type mainspring on a revolver, that required the user to wear a magnetic ring for the gun to function - this was in the 60's, long before any of the technology of today was available. This will happen eventually and we should be aiming to rescind the legislation, not just burying our heads in the sand saying it will never happen. JMHO Adios, Pizza Bob
- Meet the CZ Twins
-
Pizza Bob: Your Last Revolver is ready!
Buy the gun....that would do it.