m1garand SOLD SA M1 Garand. DELETE
-
Recently Browsing 0 members
No registered users viewing this page.
-
Supporting Vendors
-
-
Latest Topics
-
-
Similar Content
-
By medic2264
WTS M1 GARAND CORRECTED MAY 1943
RECEIVER SA 1.5 million, no pitting
BOLT 12SA "B3" heat lot
STOCK SA/EMcF with crossed cannons and serif "P"
BARREL SA 05-1943 TE 2.5 ME 3
GAS CYLINDER narrow base w/ worn finish
FRONT SIGHT SA
GAS SCREW single slot
GAS LOCK beveled edge
REAR SIGHT SA lockbar (round)
TRIGGER HOUSING 12
HAMMER SA 5
SAFETY SA 9
PLUNGER with wings
TRIGGER GUARD milled
FOLLOWER SA 11
FOLLOWER ROD SA short fork
OP ROD SA 6 no relief cut
SLING Leather Reproduction 1944
$2500 $2250 $2000 final price drop
BUYER IS RESPONSIBLE FOR ALL TRANSFER FEES
I am in Monmouth County
The first "I'LL TAKE IT" followed by a PM gets it
If you have an questions send me a PM
-
By My1stGlock
So my buddy has a stainless steel 1911 and I noticed what looked like pitting or carbon build up or dirt on the lower frame but then when I ran my finger over it it was not rough. He's cleaned it before but not sure what he's been using to clean it. Is there something that someone can recommend that he could possibly try? Pic is attached.
-
By CyclingCraig
Hi all
Looking to get another pistol and I want to buy new. Currently the top of my list is the XD Mod.2 Tactical (5").
Primary use would be range fun and I just started doing some IDPA.
This pistol would be my main choice for IDPA (That is why I wanted a 5" barrel). I have other things for nightstand/HD so this one would be as a backup to have around but mostly fun.
I wanted a 5" for longer sight radius, less flip (More weight out front) and overall greater accuracy. (BTW all my firearms are MUCH more accurate than my eyes will ever be, but looking for any advantage I can get)
I can't afford a 1911 right now, so that is not in play. I looked at the Glock 43 and Glocks just don't fit me well. The M&P M2.0 just came out. I have an M&P now, but not sure I want the same pistol just with a longer barrel?? Change things up / Variety is fun.
So anyone out there with the XD Mod.2 Tactical?
Is the PRP trigger necessary (Currently use to APEX in my M&P)?
Thanks
-
-
Posts
-
By Cheflife15 · Posted
I think this ammo was bought during the pandemic where it seems like quality control went out the window. I should have taken a picture of the primers today after shooting. Some had some pretty deep indents. I shoot da/sa. The thing that was a bit alarming was sometimes it didn't go off on the second attempt of dropping the hammer and sometimes it did. -
It’s possible it’s the ammo. Try a box of something from Federal-Federal primers are known to be the ‘softest’. If you get misfires still, the gun is again the prime suspect of course you’ll ultimately want it to run with any ammo, but I’ve known revolvers that can’t seem to get to 100% ignition double action with any other primer
-
By Cheflife15 · Posted
I've been getting light primer strikes lately with my CZ. It's happening mostly with some remington 9mm I bought. It has an extended firing pin and is certainly hitting the primer so I don't believe it's that. Maybe the spring needs replacement? I did the pencil test and the pencil flew about 7 feet. Is it just hard primers/crappy ammo? Gun has about 7/8k rounds through it. -
By GrumpyOldRetiree · Posted
Happened almost a year ago (5/23/23) on Easton Ave. Has anyone heard anything more about this? I can't find anything on on google.
-