lunker 274 Posted January 23, 2012 I am getting ready to send my S&W M&P 9L off to Dan Burwell and get his standard trigger job. I want to make it my primary gun-games pistol (IDPA SSP and USPSA Production). I have shot another member's here who had Dan's Competition trigger job and it was scary light (~2lbs if I had to guess). The standard trigger has the pull at about 4lbs, which is fine for me. Dan also offers pre-travel reduction and over-travel reduction. I am not getting the pre-travel work because I generally prefer a bit of pre-travel in my guns that don't have a thumb safety. In a 1911, mentally I know that once the safety comes off, any pressure on the trigger means the gun fires. In my non-1911 pistols, I like that I can lightly stage the trigger and have some pull before it goes bang. I don't want a safety-less striker gun that behaves like a 1911. I am curious about the over-travel work. Is there a real advantage? I guess it allows you to get to the reset easier. Anything else? Quote Share this post Link to post Share on other sites
bry@n 195 Posted January 23, 2012 I thought about sending mine to him and sent an email to him. Never got a response. I think his TJ is only like $65 or something like that and Jonf's is sweet. I agree though, I wouldn't want it to be so light. I'd like to see how your's comes out. Keep us updated. Quote Share this post Link to post Share on other sites
Wastegate 9 Posted January 23, 2012 Just get some APEX Tactical parts and you'll be good to go. Quote Share this post Link to post Share on other sites
Babaganoosh 192 Posted January 23, 2012 They are instituting a minimum trigger pull of 3 pounds for production guns in case you didn't know. So be careful if you lighten it too much. Quote Share this post Link to post Share on other sites
lunker 274 Posted January 23, 2012 Just get some APEX Tactical parts and you'll be good to go. I considered it, but went with Burwell based on some members on other forums whose opinions I trust. The best part is, I can always swap to APEX for $100 if I don't like it. Quote Share this post Link to post Share on other sites
JonF 79 Posted January 23, 2012 Chris, there are plenty of option here... you can get the standard job in lieu of the competition job if it would make you feel more comfortable. Its 1 lb heavier than the competition job and purportedly more crisp in the break as a result of it. My trigger actually measures at 2.75 Lbs with my lyman gauge which is a tad heavier than the normal job due to the "forward break" option i had him do. I agree that the pretravel is not worth worrying about but the overtravel, especially if you have him do a forward break, is essential otherwise the gun can pull shots low. These pistols have a lot of overtravel and when the sear breaks, the trigger comes crashing into the back of the trigger guard and influences guns' POA so its almost a necessary option unless you either condition the **** out of your trigger discipline or just aim high all the time. If you're not getting the forward break option, it may not be as essential. I have noticed that SIG's have the same level of overtravel in SA mode and whenever i shoot someone's, i always hit a few inches low because of it. On paper, 2-3LB triggers seem low but you'll easily grow accustomed to it, especially given your experience. What are you shooting now in production? Quote Share this post Link to post Share on other sites
lunker 274 Posted January 23, 2012 Thanks Jon. I am unfamiliar with the forward break option. Does it mean that he has the trigger break further forward in the travel? I assume that my fingers are not as long as yours, so there is a good change I wouldn't need that option. From what I have read, the Burwell standard trigger job is not as far back as the Apex kit. Hopefully that is true. Quote Share this post Link to post Share on other sites
JonF 79 Posted January 23, 2012 Yes, thats precicely what the forward break is. In most cases, trigger work to the M&P, be it custom or APEX parts, move the break far rearward and in the case of the apex kit, *all* the way rearward. While as a side effect it all but elimiates overtravel, many people don't like the position as it feels cramped to all but the smallest of grips (and remember you can always change your grip insert to small if thats an issue). The forward break is actually set to mimic the stock break position so its not abnormally further or anything like that so if you're OK with the ergo's stock, you'll like that option too. Some prople just dont like the rear set break and even apex knows this which is why they came out with the new FSS kit although that is not production legal at this time. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted January 23, 2012 I have the original burwell trigger job. Breaks at about 3.8lbs. What he normally does will eliminate a lot of over travel unless you get the forward set job. If you like to prep the trigger, and don't have really long fingers, I'd just get the standard trigger job. Quote Share this post Link to post Share on other sites
lunker 274 Posted January 24, 2012 Thanks Raz-O. My hands are big, but fingers are stubby. I am thinking about getting the standard job. Would you recommend the welded overtravel stop he puts in for $25? Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted January 24, 2012 Never ran into one in person to have an opinion about it. Frankly, below a certain weight and smoothness, it's all about how well It fits you personally. With the default job, it will stop basically when the back of the trigger hits the frame, with break being just slightly ahead of that. Quote Share this post Link to post Share on other sites
ronhonda 86 Posted January 24, 2012 They are instituting a minimum trigger pull of 3 pounds for production guns in case you didn't know. So be careful if you lighten it too much. http://www.uspsa.org/uspsa-online-mtg-details.php?meeting=30&type=meeting 3lb rule has been recinded. Quote Share this post Link to post Share on other sites
Babaganoosh 192 Posted January 25, 2012 http://www.uspsa.org...30&type=meeting 3lb rule has been recinded. Ahhh, Yeah they went bonkers over on the Enos forum about how it originally went down Quote Share this post Link to post Share on other sites
rauchman 3 Posted January 25, 2012 Greetings, I have an M&P40 that I've done some work to. Let me preface by saying, I've never shot a Dave Burwell trigger jobbed M&P. What I have done on mine is.... Installed and polshed the Apex sear Gone to Dave Burwell's site and done his home trigger job. Basically, it calls for smoothing all contact surfaces. Also, it calls for rounding the firing pin safety plunger more deeply/more rounded. I don't have anything to test the weight of the trigger, but I'm guessing it's roughly 4.5-5lbs. It is extremely smooth. It still has the normal takeup and overtravel, but as has been mentioned, unless I was going for a thumb safety, this setup is ok for me. If you do decide to do the work yourself, I HIGHLY suggest getting the sight pusher. The only way to get to the firing pin safety plunger, is by removing the rear sight. I have it, if you need to borrow it. Quote Share this post Link to post Share on other sites
lunker 274 Posted January 25, 2012 Thanks for the offer Rauchman. I sent mine to Burwell yesterday. I am hoping to have it back by next week. The worst part of all this is the shipping charges. Hopefully we can meet up sometime and compare triggers. Quote Share this post Link to post Share on other sites
JonF 79 Posted January 25, 2012 I initially polished my own stock sear the Burwell way like rauchman did, but i wasn't thrilled with it since it still a little heavy and had lots of overtravel. Thats why i sent it out too; it just doesn't even remotely compare to what a seasoned expert can do. What options did you eventually go with? Quote Share this post Link to post Share on other sites
lunker 274 Posted January 25, 2012 None really. I just got the standard trigger job. No forward positioning, pre-travel or over-travel mods either. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted January 26, 2012 Just FYI, the pdf burewell hosts is not exactly the way he does his trigger job. He didn't make it, he just makes it available. Quote Share this post Link to post Share on other sites