sroc112 24 Posted March 21 Sorry not all pics super clear. Had a basic muzzle brake pinned and welded to a new upper. Look the way it should on this style brake? Quote Share this post Link to post Share on other sites
Cheflife15 455 Posted March 21 Respectfully that looks pretty rough. Where did you have that done? My last 2 weld jobs, I couldn't even find the spot without a flashlight. Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 21 Point Blank in East Hanover Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 21 I'm not worried about the brake being ruined, it's a cheap basic a2 style brake. But I would feel better knowing I can have it removed and have a new one done by someone else, but I guess there is no way to know if it can be removed without destroying the thread until you actually try and remove it, and then may be too late of it was too deep to salvage. Quote Share this post Link to post Share on other sites
Cheflife15 455 Posted March 21 Most competent gun smith's can removed a pin and weld job without damaging the barrel. Gun for hire does nice work. Monmouth arms also does really nice work. Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 21 I was originally going to use monmouth arms but decided to ise this place as it was the most convenient for location at the time. 1 guy there was cool but the other dude I dealt with a few times, who was the one who did the work, was an asshole. I'll never go there again. Quote Share this post Link to post Share on other sites
diamondd817 827 Posted March 21 9 minutes ago, sroc112 said: I'm not worried about the brake being ruined, it's a cheap basic a2 style brake. But I would feel better knowing I can have it removed and have a new one done by someone else, but I guess there is no way to know if it can be removed without destroying the thread until you actually try and remove it, and then may be too late of it was too deep to salvage. That's a shit job, and the chances are you can't remove that without damaging the barrel/threads. Hence, the pin and welded nonsense. You should have went to FSS which is 5 minutes away. Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 21 Disappointing. Glad it wasn't on an expensive upper and the cost for the compliancy work was also not expensive at all. Live and learn but for my first AR it's a bummer. Quote Share this post Link to post Share on other sites
diamondd817 827 Posted March 21 17 minutes ago, sroc112 said: Point Blank in East Hanover And before that they were called County Line Firearms. I wouldn't even consider stepping foot in their establishment just from reading their store policy nonsense on their website. I guess most felt he same way, and that's why they went out of business/sold out. To hell with any gun store that adds unnecessary additional requirements and bullshit on top of NJ' bullshit. Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 21 Never went in there when it was county line, so didn't have any prior experience with them. From my understanding they bought out one of the other owners and renamed. Quote Share this post Link to post Share on other sites
glockncolts 50 Posted March 22 I am a weld supervisor and I would fire that guy......... 1 Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 22 My first ar so I didn't know any better when I picked it up, but knew it didn't seem right. Did some more research when I got home and then just got pissed. Worst part about it now looking back is how much of a dick this guy was and the stupid comments he kept making. I won't be going back there for anything. 2 minutes ago, glockncolts said: I am a weld supervisor and I would fire that guy......... Chances you think something like this can be removed without destroying the barrel so I can have it redone? Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 22 That pin hole is so far up the brake, I don't even know if it's notched into the actual barrel or sitting on top of the muzzle tip. 1 Quote Share this post Link to post Share on other sites
glockncolts 50 Posted March 22 21 minutes ago, sroc112 said: My first ar so I didn't know any better when I picked it up, but knew it didn't seem right. Did some more research when I got home and then just got pissed. Worst part about it now looking back is how much of a dick this guy was and the stupid comments he kept making. I won't be going back there for anything. Chances you think something like this can be removed without destroying the barrel so I can have it redone? Easy peasy. Just needs to be ground down until you see a line where it is not fused.... Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 22 You're a pro welder? Or was that a sarcastic comment amount firing that guy? Where you located Quote Share this post Link to post Share on other sites
glockncolts 50 Posted March 22 1 minute ago, sroc112 said: You're a pro welder? Or was that a sarcastic comment amount firing that guy? Where you located Aws certified weld supervisor.. I am in south jersey by vineland... Any welder with a pulse should be able to do that job.... Quote Share this post Link to post Share on other sites
njJoniGuy 2,131 Posted March 22 This story is a reminder of two basic tenets of life:: 1) You generally only get what you pay for. and 2) Life is too short to deal with people who come across as assholes ... they usually are! 2 Quote Share this post Link to post Share on other sites
silverado427 10,731 Posted March 22 Wow. That’s a fugin hack job… Quote Share this post Link to post Share on other sites
ESB 247 Posted March 28 The dude who did that is not a welder. He's a grinder. Quote Share this post Link to post Share on other sites
Bomber 1,092 Posted March 28 On 3/22/2024 at 8:43 AM, njJoniGuy said: This story is a reminder of two basic tenets of life:: 2) Life is too short to deal with people who come across as assholes ... they usually are! Gun store a-holes and and pin/weld jobs like that are the reason I gladly drive an hour to Monmouth Arms.. 1 Quote Share this post Link to post Share on other sites
sroc112 24 Posted March 29 Seperate question - I have a Magpul STR stock on this gun. There is no pin or hole visible anywhere on the stock from the pin job. They mentioned that they put something in between the little trigger piece on the stock that you squeeze to adjust it, so that it can't be moved. Mentioned that it can be removed if needed, although not easy to do with just your hands on the fly. They made it seem this was a better way to go about the pin, cosmetically anyway. It almost appears like that little trigger piece on the stock is fully squeezed in, and then some internal pin placed somewhere within that mechanism to keep it from moving. Anyone familiar with this method? Assuming since it makes the stock no longer adjustable, even temporarily, it solved the restriction around it. Or am I wrong? Quote Share this post Link to post Share on other sites
Displaced Texan 11,752 Posted March 31 On 3/29/2024 at 2:25 PM, sroc112 said: Seperate question - I have a Magpul STR stock on this gun. There is no pin or hole visible anywhere on the stock from the pin job. They mentioned that they put something in between the little trigger piece on the stock that you squeeze to adjust it, so that it can't be moved. Mentioned that it can be removed if needed, although not easy to do with just your hands on the fly. They made it seem this was a better way to go about the pin, cosmetically anyway. It almost appears like that little trigger piece on the stock is fully squeezed in, and then some internal pin placed somewhere within that mechanism to keep it from moving. Anyone familiar with this method? Assuming since it makes the stock no longer adjustable, even temporarily, it solved the restriction around it. Or am I wrong? When I lived in NJ, that’s how I had my stocks ‘pinned’. It meets the spirit of the law, in the respect that the stock cannot be adjusted. One would have to use tools to take the stock apart and change the LOP. 1 Quote Share this post Link to post Share on other sites