Teky0101 6 Posted July 10, 2012 Hello Everyone, Does anyone know the best way to clean out a gas tube on an ar15? I have been experiencing some feeding issues lately where one round ejects gets stuck loading the second round. It sticks so bad that I have to pull on the charging handle really hard, ejecting the round which then crimps the case destroying the bullet. Quote Share this post Link to post Share on other sites
bhunted 887 Posted July 10, 2012 http://m.youtube.com/#/watch?desktop_uri=/watch?v=R4mcUReVQko&v=R4mcUReVQko&gl=US Sent from John's iPad 2 via Tapatalk HD Quote Share this post Link to post Share on other sites
DirtyDigz 1,812 Posted July 10, 2012 I'm no AR expert, but are you sure your issue is due to an occluded gas tube? I thought gas tubes rarely, if ever, needed cleaning (usually good for 10,000 rounds or more) I'd be looking elsewhere for your feeding problem. Is the bcg running smoothly back and forth? Any issues with your magazine, feed lips, magazine follower or feed ramps? Quote Share this post Link to post Share on other sites
robot_hell 72 Posted July 10, 2012 I'm no AR expert, but are you sure your issue is due to an occluded gas tube? I thought gas tubes rarely, if ever, needed cleaning (usually good for 10,000 rounds or more) I'd be looking elsewhere for your feeding problem. Is the bcg running smoothly back and forth? Any issues with your magazine, feed lips, magazine follower or feed ramps? I agree with the above, how did you come to the conclusion it's the gas system? I'm not clear on what's happening-- The old round ejects, and the new round sticks in the chamber? If you can give a detailed description (or picture) of how it jams and when, I'm sure someone can help you Quote Share this post Link to post Share on other sites
Teky0101 6 Posted July 10, 2012 Thank you for the help, the gun chambers and fires but when the round ejects the next round gets stuck inside the magazine with the bolt face on top mangling the next round. Anyone have any ideas? It seemed to do this a lot with remmington ammo but when I switched to my usual PMC X-tac it only did it twice. The mags are good since they are pmags and shoot great. I thinks its an issue with my gun it shot wonderful up to this point. Quote Share this post Link to post Share on other sites
Turbotezza 1 Posted July 10, 2012 Your're probably just undergassed. As others have mentioned, it is unlikely that your gas tube is fouled as 10,000 psi of gas pressure passing through won't leave built up carbon crud in there. I'm quite sure that if you use 5.56mm NATO ammo, you'll won't have a problem with cycling. To help with your issues, you could; 1) A good general clean of the BCG. 2) Use better ammo. 3) Lighter(lower power) buffer spring 4) Lighter hammer spring 5) Lighter buffer Of course, you could also enlarge the gas port in the barrel. Quote Share this post Link to post Share on other sites
Teky0101 6 Posted July 10, 2012 I was actually using 5.56 PCM 62 grain xtac ammo and still had a few of these issues. Could to much oil cause this issue? Quote Share this post Link to post Share on other sites
Tactical Turtle 11 Posted July 10, 2012 Get some spray degreaser, I use the Orange organic crap, take your bcg apart spray down the parts. Let it sit for atleast 20 minutes, do the same to your upper, spray it down and let it sit. U can't use to much so.use a lot. Spray it all down with hot water and wipe dry. This should clean up all the loose carbon and old grease. Next take the internals of your bcgn inspect.for any cracks, broken springs (extractor spring) and make sure the rings are intact and move freely. Now.check the neck of the bolt, if there is a lot of built up carbon there soak in some.hooppes and scrub with a brass brush. Now clean the inside of the bolt carrier. Lightly lubricate the moving parts and reassemble. Put a few drops of good oil on the out if the bcg and rub it around. I add one drop to the actual upper towards the back and let her run. If its still not chambering a round a part is failing. Try new mags and someone elses bcg. Quote Share this post Link to post Share on other sites
Tactical Turtle 11 Posted July 10, 2012 Can also be a really dirty feed ramp, if you don't have the tools to remove the barrel, spraying hoppes right in there, and using a brass 22 cleaning set up with a plastic rod so.u can bend it a little will help. Use a qtip to get as much loose crap out of there, then spray again with hoppes, rinse it out, dry and see what happens. Doubt its a gas tube issue. Oh yea check ur buffers, pull it out and clean it up, Maybe some dirt in there not letting the spring reset the bcg propperly or fast enough. If ur local to me you can use my.mags and bcg if u want to narrow down your issues Quote Share this post Link to post Share on other sites
Old School 611 Posted July 10, 2012 Your're probably just undergassed. As others have mentioned, it is unlikely that your gas tube is fouled as 10,000 psi of gas pressure passing through won't leave built up carbon crud in there. I'm quite sure that if you use 5.56mm NATO ammo, you'll won't have a problem with cycling. To help with your issues, you could; 1) A good general clean of the BCG. Yes and check the gas key for dirt or loosness 2) Use better ammo. Always 3) Lighter(lower power) buffer spring NG, It sounds like it worked previously 4) Lighter hammer spring NG, It sounds like it worked previously 5) Lighter buffer NG, It sounds like it worked previously Of course, you could also enlarge the gas port in the barrel. Absolutely not if it worked before Sounds like it is short stroking. A good cleaning and run wet. Try again. Clean gas tube is ok esspecially if you were shooting cheap commie stuff at any time. Just dry out the tube when you're done. To check the mag, drop the bolt from lock on a mag with one or two rounds to check for a weak spring. Do it under safe conditions please. Quote Share this post Link to post Share on other sites
Turbotezza 1 Posted July 10, 2012 To me it sounds that he has a marginally undergassed and short stroking, which is proably why is 5.56 ammo works better than the Rem 223. Going to lighter springs/buffer and a larger gas port will help his situation. Some oil is good, but overlubing just blows oil in your face when you start shooting. Sounds like it is short stroking. A good cleaning and run wet. Try again. Clean gas tube is ok esspecially if you were shooting cheap commie stuff at any time. Just dry out the tube when you're done. To check the mag, drop the bolt from lock on a mag with one or two rounds to check for a weak spring. Do it under safe conditions please. Quote Share this post Link to post Share on other sites
Old School 611 Posted July 10, 2012 To me it sounds that he has a marginally undergassed and short stroking, which is proably why is 5.56 ammo works better than the Rem 223. Going to lighter springs/buffer and a larger gas port will help his situation. Some oil is good, but overlubing just blows oil in your face when you start shooting. I tend to agree with you. My BIG question was it working before and with what ammo? Quote Share this post Link to post Share on other sites
Teky0101 6 Posted July 10, 2012 99% of the time I shoot PMC x-tac. The issue actually started right after I cleaned it. I am going to clean it again and inspect the parts. Quote Share this post Link to post Share on other sites
robot_hell 72 Posted July 10, 2012 I'd check the gas key first. I had the exact same problem you describe, mangled brass and everything. Turns out the screws on the gas key were loose-- I tightened them down, had them staked, and all was well. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted July 10, 2012 What exactly do you think a $0.05 pipe cleaner is going to get out of the way that 15,000 to 20,000 PSI is not? It sounds like you are under gassed and short stroking. Whose barrel, waht length gas system, what gas block, what buffer, what buffer spring, what BCG, what bolt, what mags. what weight bullet? Quote Share this post Link to post Share on other sites
Teky0101 6 Posted July 10, 2012 I have an s&w m&P Optics Ready Compliant. Its a 16" barrel without a comp and has a 1/9" twist. The gas system is a standard ar gas system not sure about the buffer and springs its stock with the gun. I did however change the stock a while back to an ACE Skeleton Entry stock. The bolt is a standard s&w bolt. I am using capped PMAGS and PMC X-TAX 62 grain Green Tip. I have shot many rounds in its current config without and it functioned awesome. Not sure what happed when I cleaned it. I will check the gas key screws to make sure they are tight, where are they located? Quote Share this post Link to post Share on other sites
Krdshrk 3,878 Posted July 10, 2012 They're on the BCG itself - the top screws that hold the gas tube on. Quote Share this post Link to post Share on other sites
Fullhouse 0 Posted July 10, 2012 Gas key is located at the top of the bcg( bolt carrier group) . It is the part that the gas tube engages. There are 2 cap head screws that attach it to the carrier, these screws should be staked to prevent them from loosening up Quote Share this post Link to post Share on other sites
junkmanted 54 Posted July 10, 2012 I had one clog ,, take it out, use carb cleaner and blow out with compressed air. Quote Share this post Link to post Share on other sites
T Bill 649 Posted July 10, 2012 I don't know if this is an issue here or not. Added a sling mount to a A2 type stock recently. The kit included a new stock retainer screw for the added space from the end of the existing tube and the butt end of the stock. After installing it the BCG didnt fully cycle, stopping short of a full stroke. Took out screw and replaced and problem when away. Cause....the screw was too long not letting the buffer fully cycle and holding up the BCG. That is the first time I ever experienced something that weird. Quote Share this post Link to post Share on other sites
Mr.G 8 Posted July 10, 2012 Here is the gas tube cleaner. http://www.brownells.com/.aspx/pid=1544/Product/AR-15-GAS-TUBE-CLEANERS However, this is just for maintenance and not to the solution of your problem. Plenty have provided useful insight. Quote Share this post Link to post Share on other sites
vladtepes 1,060 Posted July 11, 2012 The issue actually started right after I cleaned it. I am going to clean it again and inspect the parts. worked properly you cleaned it now does not work properly logic tells me you likely did something wrong and it has nothing to do with any complicated solution.. Quote Share this post Link to post Share on other sites
Teky0101 6 Posted July 13, 2012 I went to a local gun shop today to pick up my fathers gun which we had blued for fathers day. While I was there I spoke with the owner who is a fantasic gun smith. He told me a few things that can cause a short stroke in an AR. One thing was the gas key screws getting loose and this can happen after staking. Other issues include the buffer not being turned the right direction, bad buffer tube springs, to much oil and weak gas seals on the bolt. I also asked about the gas tube and cleaning it and he advised me never to stick anything is the gas tube since it gets obstructed and would require a large dissassembly to fix this issue. I am going to check out the gun shortly to see what's going on. Thank you for your help everyone! Quote Share this post Link to post Share on other sites