Jon 264 Posted May 15, 2013 The Palm Beach sheriff’s office is reporting an unfortunately notable streak of failures with their Glock service pistols. CBS4 obtained a confidential Sheriff’s report documenting the department’s Glock issues. All of the Palm Beach sheriff’s problems have been striker-related, and the report is simply called “Firing Pin Issue.” In all instances of the problem, faulty strikers were causing failures to fire. Other law enforcement agencies have heard of the Palm Beach sheriff’s department’s problems, with the Miami Dade PD even making a five-minute PSA video warning officers about the problem and how to check against it. http://www.guns.com/2013/05/14/florida-sheriffs-office-reports-problems-with-glock-service-pistols-video/ Quote Share this post Link to post Share on other sites
GRIZ 3,369 Posted May 15, 2013 It would make sense that we hear about LE having more problems with Glock than other manufacturers as 60-70% of LE agencies use Glocks. Quote Share this post Link to post Share on other sites
Krdshrk 3,878 Posted May 15, 2013 Glock blamed the ammo.... lol.... yeah LE ammo is the cause.... Quote Share this post Link to post Share on other sites
RubberBullets 65 Posted May 15, 2013 "Glock Perfection" Quote Share this post Link to post Share on other sites
High Exposure 5,671 Posted May 15, 2013 Glock blamed the ammo.... lol.... yeah LE ammo is the cause.... Ammo may not always be the case and Glock and really does suck sometimes when these issues crop up. But... The QC of ammo manufacturers is currently at an all time low. I regularly see primers set too deep in the pockets, primers installed backwards or sideways, just plain bad primers in general, no flash hole in the case, no powder in the case, bullet set at an angle, cases crimped or rolled at the neck. In 10 years as a fireams instructor overseeing well over 25,000 rounds a year in student guns (pistol, rifle, subgun, & shotgun) and an additional 5000 - 10000 rounds a year that I shoot myself, I have never seen the amount of ammo related problems that I have seen in the last year and a half. Add the typical cops reluctance to maintain their weapon or to properly rotate ammo when loading/unloading their pistol and you will get these issues. Also, as GRIZ stated, when 60-70% of Law Enforcement Agencies I this country carry Glock, you will hear about their failures proportionally more than others. I have had to swap my striker on a few of my Gen 3 .40 Glocks as it approached the appropriate round count. It is a wear part and has a finite service life. Preventative Maintenance is important. Understand that I am not saying that Glock is incapable of making a bard part, or that MIM strikers are a good idea. I am stating that it seems like there is more to this story. Quote Share this post Link to post Share on other sites
Maksim 1,504 Posted May 15, 2013 Jon, you are a hater.... This could of happen to any gun. But hey, at least Glock knows how the bullets go into a mag. =) Quote Share this post Link to post Share on other sites
jrfly3006 42 Posted May 15, 2013 Nice catch Maks... Glock always sends a rep immediately to a dept having ANY trouble.. And they replace any parts needed for free ASAP.. As my dept armorer told me once ..anytime theres a problem with our MP-5's its a minimum $250.00 per gun fix from HK.. Now thats service Quote Share this post Link to post Share on other sites
Maksim 1,504 Posted May 15, 2013 Nice catch Maks... Glock always sends a rep immediately to a dept having ANY trouble.. And they replace any parts needed for free ASAP.. As my dept armorer told me once ..anytime theres a problem with our MP-5's its a minimum $250.00 per gun fix from HK.. Now thats service Actually, I do dislike glocks... but over time, I value their company and support for shooting sports. As much as anyone can hate on Glock.... you can't argue about the fact that on the whole, they are probably the most reliable pieces of tactical Tupperware out there. Edit.... Here is where I earned respect for glock. A shooter on another forum, blew up his gun in a KB after he double charged a case. The gun was fubared. He sent it in to Glock to see if any parts were still good, with a note that HE and his reloads were responsible. They replaced his entire gun, for $70. How is that for service? Quote Share this post Link to post Share on other sites
Old Dog 19 Posted May 15, 2013 Just keep repeating, "Glock Reliability" and Sig's "to hell and back" often enough until you believe it. I have had two guns from each manufacture jam so bad that I was given full refunds for each. Quote Share this post Link to post Share on other sites
NYMetsFan86 9 Posted May 15, 2013 Jon, you are a hater.... This could of happen to any gun. But hey, at least Glock knows how the bullets go into a mag. =) image.jpg I always enjoy that catalog cover haha never gets old. Quote Share this post Link to post Share on other sites
Maksim 1,504 Posted May 15, 2013 But I do love HK guns.... Hand guns. They really are high quality and über reliable. Quote Share this post Link to post Share on other sites
blksheep 466 Posted May 15, 2013 Ammo may not always be the case and Glock and really does suck sometimes when these issues crop up. But... The QC of ammo manufacturers is currently at an all time low. I regularly see primers set too deep in the pockets, primers installed backwards or sideways, just plain bad primers in general, no flash hole in the case, no powder in the case, bullet set at an angle, cases crimped or rolled at the neck. In 10 years as a fireams instructor overseeing well over 25,000 rounds a year in student guns (pistol, rifle, subgun, & shotgun) and an additional 5000 - 10000 rounds a year that I shoot myself, I have never seen the amount of ammo related problems that I have seen in the last year and a half. Add the typical cops reluctance to maintain their weapon or to properly rotate ammo when loading/unloading their pistol and you will get these issues. Also, as GRIZ stated, when 60-70% of Law Enforcement Agencies I this country carry Glock, you will hear about their failures proportionally more than others. I have had to swap my striker on a few of my Gen 3 .40 Glocks as it approached the appropriate round count. It is a wear part and has a finite service life. Preventative Maintenance is important. Understand that I am not saying that Glock is incapable of making a bard part, or that MIM strikers are a good idea. I am stating that it seems like there is more to this story. As stated QC of ammo is at an all time low. Quote Share this post Link to post Share on other sites
blksheep 466 Posted May 15, 2013 Jon, you are a hater.... This could of happen to any gun. But hey, at least Glock knows how the bullets go into a mag. =) image.jpg Doh! Quote Share this post Link to post Share on other sites
Jon 264 Posted May 15, 2013 Dude, HKs are so awesome, they shoot even when you put the ammo in backwards! Quote Share this post Link to post Share on other sites
blksheep 466 Posted May 15, 2013 Dude, HKs are so awesome, they shoot even when you put the ammo in backwards! I can tell you from experience that they don't. Quote Share this post Link to post Share on other sites
tony357 386 Posted May 15, 2013 You have too look on the flip side of things... Quote Share this post Link to post Share on other sites
blksheep 466 Posted May 16, 2013 You have too look on the flip side of things... Lol Quote Share this post Link to post Share on other sites
Nikos 31 Posted May 16, 2013 Edit.... Here is where I earned respect for glock. A shooter on another forum, blew up his gun in a KB after he double charged a case. The gun was fubared. He sent it in to Glock to see if any parts were still good, with a note that HE and his reloads were responsible. They replaced his entire gun, for $70. How is that for service? Nice, they allowed their customer to pay manufacturer's cost on the product. Quote Share this post Link to post Share on other sites
hiker88 22 Posted May 16, 2013 Good to know the possible weakness of a component... Glock strikers (oem and aftermarket ) are plentiful and easy enough to change during maintenance intervals. Quote Share this post Link to post Share on other sites
Socom 19 Posted May 16, 2013 Jon, you are a hater.... This could of happen to any gun. But hey, at least Glock knows how the bullets go into a mag. =) Puke expensive plastic gun Quote Share this post Link to post Share on other sites
blksheep 466 Posted May 16, 2013 Nice, they allowed their customer to pay manufacturer's cost on the product. You have to factor in labor, marketing, research and development etc... Quote Share this post Link to post Share on other sites
Cowboy6373 0 Posted May 16, 2013 I was at a local LEO range for my sons 4H and found a lot of live ammo on the ground, mostly 40 cal. What I noticed were primer strikes but no boom. On close inspection, it appeared that the case was almost roll crimped. In a straight wall case this would explain strikes with no boom as the cartridge headspaces on the case mouth. With a hard taper or almost roll crimp, the striker would push the round forward and cause it not to fire. So it may not be Glocks fault in this case. I'm not defending Glock, but without knowing the other components, it is hard to blame any one thing. Quote Share this post Link to post Share on other sites
zoid 24 Posted May 21, 2013 When I use Tula or Wolf primers I get about 10-15 light strikes per 1000 round with my Glocks. . Hammer fired pistols maybe 3-5 per 1000. Striker fire pistols can be more suseptable to ammo issues as noted above. But I imagine LE ammo would have very sensitive primers. I'm no expert though. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted May 21, 2013 Glock blamed the ammo.... lol.... yeah LE ammo is the cause.... COuld be. With the demand on the ammo manufacturing pipeline, they could be getting bum primers. Poorly positioned anvils, improperly sized anvils, or going with a vendor that is producing less sensitive priming compound could al cause misfire issues, especially if combined with a worn gun. It's hard to say because nobody is being specific about the type of failures occurring. pierced primers and chipped strikers could be the striker and/or failure to maintain the guns. Light strikes could be that or out of spec anvils or flipped anvils. Poor maintenance (i.e. not replacing springs) could cause timing issues which could wear the striker oddly or chip it, and result in light strikes, even with good ammo, or could make less sensitive primer compound or exceptionally thick primer cups into something that would cause a misfire. Vendors usually don't like to point out that large customers are doing something stupid. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted May 21, 2013 When I use Tula or Wolf primers I get about 10-15 light strikes per 1000 round with my Glocks. . Hammer fired pistols maybe 3-5 per 1000. Striker fire pistols can be more suseptable to ammo issues as noted above. But I imagine LE ammo would have very sensitive primers. I'm no expert though. They'd have sensitive primers? like military ammo does? Uhh no. These guys are going to be doing administrative loads and what not. THe primers will not be super sensitive. Quote Share this post Link to post Share on other sites
Tactical Turtle 11 Posted May 21, 2013 Poor ammo and a dirty striker channel could be to blame. Besides a good scrubbing on the exterior surface most owners dont take the time or spend the money to have the internal channels cleaned. Just an idea Quote Share this post Link to post Share on other sites
zoid 24 Posted May 22, 2013 They'd have sensitive primers? like military ammo does? Uhh no. These guys are going to be doing administrative loads and what not. THe primers will not be super sensitive. What does that have to do with the primer? The firing pin is not out when doing an administrative load. A more sensitive primer is more likely to go off when fired is my point. And when I say more sensitive I'm comparing a Federal to the likes of a CCI. I'm not saying the go off when dropped. Quote Share this post Link to post Share on other sites