Need a shop to pin comp and shave bayo lug

[dwamp2006 1]

So after an hour of trying to shave the bayo lug off my upper im giving up, my dremel just doesnt have the balls to do it. I was going to take the front sight post completely off and bring it to work to take to the grinder, but i cant get the pins out and i dont want to scratch anything up. 

 

Now im looking for a shop Recommendation around mt holly/lumberton area to shave the lug and pin and weld the comp. I want the job to be good so if you have personal experience with a place please let me know. Thanks!

 

Disclaimer: i do not have any operable lower receivers or other ARs while in possession of this upper....

[brocglock23 4]

Disclaimer: i do not have any operable lower receivers or other ARs while in possession of this upper....

Sure Sure

 

All joking aside I heard Ed's Gun Shop in Deptford does the work pretty well but slowly.

[checko 180]

Just curious, what attachment were you using on the dremel?

[JT Custom Guns 957]

If you give me a call - we do this work all the time..........

[RUTGERS95 890]

rahway's heritage guild pins comps for $35

[checko 180]

rahway's heritage guild pins comps for $35

 

I think that would be quite a haul for him.

[dwamp2006 1]

Just curious, what attachment were you using on the dremel?

More of a grinding wheel than a cut off wheel, but its also a cordless dremel. Good for polishing parts but not much else.

 

 

If you give me a call - we do this work all the time..........

I was hoping to find somewhere close but I have your number, ill give you a call tomorrow sometime. Comps in the mail and should be here this week sometime. Thanks!

[dwamp2006 1]

I think that would be quite a haul for him.

That it would, about an hour and half 1 way at the least. Was hoping for being a simple job i could find somewhere close. Im in a crappy area, no gun shops, few gun smiths, only 1 range and thats R14. 

[Blake 50]

I've cut a bayo lug off myself with a hand saw before.  Took about 5 min and it actually came out really clean.  Then just take a bluing pen to it and you are good to go.  YMMV.

[SJG 253]

You only need to remove the ears of the lug to make it legal. If your dremel will not do it, you can probably do it with a hack saw or use a regular power drill with a grinding wheel to get the ears off-then use some perma blue or some high heat black paint to touch it up. You do not need to weld the comp,(unless 14.5") all you need to do is pin it, so it cannot be unscrewed from the barrel.

[checko 180]

You only need to remove the ears of the lug to make it legal. If your dremel will not do it, you can probably do it with a hack saw or use a regular power drill with a grinding wheel to get the ears ofd-then use some perma blue or some high heat black paint to touch it up. You do not need to weld the comp, all you need to do is pin it, so it cannot be unscrewed from the barrel.

 

Unless its a 14.5" barrel.  Then BATFE rules apply. 

[RUTGERS95 890]

I think that would be quite a haul for him.

yes sir, I didn't see his location.....oops

[blksheep 466]

Mikes on Rt. 38?

[dwamp2006 1]

Oh, boy not trying to turn this into the same as the other thread. Simply looking for recs not how i should do it my self. 

[dwamp2006 1]

Mikes on Rt. 38?

Is that the little hole in the wall tackle/gun smith place? ever get any work done or know how good their work is?

[blksheep 466]

Bought a few guns there about 8 yeats ago. I liked em. Dont know if he does work.

[Teky0101 6]

You could check with Bangers Sport Shop in Winslow. I think they can do this. http://www.bangerssports.com/

[rightisright 3]

I know you aren't looking to do it yourself.  But this may serve as a warning to others.  Most cordless Dremel type tools lack the torque for "heavier" cutting duty.   I have a few of each type.  Like you said, the cordless is nice for light duty.  Not for cutting.  They shut down rapidly whenever a load is put on the motor to prevent over-heating.

[NJSUX 2]

I highly recommend bangers.

[Ff312 5]

Don't go to mikes took forever and not the best work. Second on bangers they are in Winslow good prices and nice work.

[gleninjersey 2,141]

Steve @ Monmouth Arms in Morganville did mine. I dropped it off, went to eat breakfast, came back and it was done. Excellent work.

[remixer 1,645]

Thanks Glenn, If hes local or willing to take a drive ill offer the same service
 

[thunderace4 0]

Tier one defense in mountainside does good work.

[PK90 3,570]

Thanks Glenn, If hes local or willing to take a drive ill offer the same service

 

You buy your customers breakfast?

[remixer 1,645]

Lol

[Golf battery 1,223]

Bangers