Ray Ray 3,566 Posted April 10, 2012 I was curious wondering if chambering and rechambering a round in a semi-auto pistol or rifle would cause a bullet to be pushed back into the case? Quote Share this post Link to post Share on other sites
AS350Driver 56 Posted April 10, 2012 Yes, reloading is dangerous remember. Quote Share this post Link to post Share on other sites
Old School 611 Posted April 11, 2012 I was curious wondering if chambering and rechambering a round in a semi-auto pistol or rifle would cause a bullet to be pushed back into the case? Only if the neck tension or crimp isn't correct. How many times are you doing this "Speedy" Quote Share this post Link to post Share on other sites
Ray Ray 3,566 Posted April 11, 2012 I wasn't talking about reloading ladies. Quote Share this post Link to post Share on other sites
Ray Ray 3,566 Posted April 11, 2012 Thanks again Pete Quote Share this post Link to post Share on other sites
AS350Driver 56 Posted April 11, 2012 I know I was busting your chops, but what old school said is correct that if the crimp or neck tension isn't correct then yes you could experience set back even with factory ammo. If you have a set of calipers measure it before you start and again when you're done. Quote Share this post Link to post Share on other sites
robot_hell 72 Posted April 11, 2012 Yes, absolutely. Even if neck tension is correct it will eventually happen. The Golden Sabers I use in my 1911 have already started to do this after 5 or 6 chamberings. Quote Share this post Link to post Share on other sites
Old School 611 Posted April 11, 2012 I wasn't talking about reloading ladies. Nobody is talking about reloading Shirley. I was talking about factory ammo. And I couldn't watch that whole video because it was such BS. When I load my defense gun in the house I ease the slide down anyway. Quote Share this post Link to post Share on other sites
stever 16 Posted April 11, 2012 If one is longer just hammer it in so they're all the same =@ Quote Share this post Link to post Share on other sites
Ray Ray 3,566 Posted April 11, 2012 Nobody is talking about reloading Shirley. I was talking about factory ammo. And I couldn't watch that whole video because it was such BS. When I load my defense gun in the house I ease the slide down anyway. thanks grandpa Quote Share this post Link to post Share on other sites
NickC 23 Posted April 11, 2012 Yes, reloading is dangerous remember. HA! I thought it was funny Frank... Anyway, i just chambered a Federal 9mm 10 times in my STI 9mm and it went from 1.15 down to 1.143. 7mils or the thickness of 2 human hairs. Quote Share this post Link to post Share on other sites
Old School 611 Posted April 11, 2012 HA! I thought it was funny Frank... Anyway, i just chambered a Federal 9mm 10 times in my STI 9mm and it went from 1.15 down to 1.43. 7mils or the thickness of 2 human hairs. Recheck your numbers or explain. I'm confused. Quote Share this post Link to post Share on other sites
NickC 23 Posted April 11, 2012 Recheck your numbers or explain. I'm confused. 1.143 Wow big diference there. Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted April 11, 2012 Only if the neck tension or crimp isn't correct. How many times are you doing this "Speedy" That's not so. Even with factory ammo that is sealed with an adhesive, you can get bullet setback form administrative reloads. Yes, properly constructed ammo won't set back under recoil, but if you are a cop who is unloading for whatever reason (usually mandated administrative unload/reload for certain locations), then rechambering the same round when you reload over and over and over, you can have severe bullet setback that is dangerous. If you mimic the same pattern of behavior with your HD weapon by clearing it an putting it in the safe each morning, and loading it and making it handy each evening, you have to watch out for the same thing. Quote Share this post Link to post Share on other sites
GRIZ 3,369 Posted April 11, 2012 I've seen bullets set back in factory ammo often. I used to caution agents regarding this as some unloaded every night when they went home, reload in the morning, and repeat the process when they entered and left the office. Some people didn't want to wear a gun in the office so they would unload it and put it in a lockbox while there. A loaded round can't be expected to cope with dozens of loadings no matter how correct the neck tension or crimp may be. Quote Share this post Link to post Share on other sites
JackDaWack 2,895 Posted April 11, 2012 Make sure you stack your ammo correctly as well. One direction provides support via the tray, the other way and your bullets take all the pressure. Quote Share this post Link to post Share on other sites
Old School 611 Posted April 11, 2012 That's not so. Even with factory ammo that is sealed with an adhesive, you can get bullet setback form administrative reloads. Yes, properly constructed ammo won't set back under recoil, but if you are a cop who is unloading for whatever reason (usually mandated administrative unload/reload for certain locations), then rechambering the same round when you reload over and over and over, you can have severe bullet setback that is dangerous. If you mimic the same pattern of behavior with your HD weapon by clearing it an putting it in the safe each morning, and loading it and making it handy each evening, you have to watch out for the same thing. Any mechanical device such as a bullet can be abused. I stand by my statement. Proper ammo will not set back under normal circumstances. If you are going to repetedly drop the slide on the same round inertia will have some effect. There are ways to aviod the bullet set back. Quote Share this post Link to post Share on other sites
Sigman 41 Posted April 11, 2012 Any mechanical device such as a bullet can be abused. I stand by my statement. Proper ammo will not set back under normal circumstances. If you are going to repetedly drop the slide on the same round inertia will have some effect. There are ways to aviod the bullet set back. Frank - I have to agree with the others that set back happens with properly crimped ammo. I've noticed varying amounts of set back with different bullet types. For example, I noticed set back more prominent in .45ACP wad cutters. I believe bullet shape and angle during chambering a round will affect set back and will also vary between guns. Quote Share this post Link to post Share on other sites
Old School 611 Posted April 11, 2012 Frank - I have to agree with the others that set back happens with properly crimped ammo. I've noticed varying amounts of set back with different bullet types. For example, I noticed set back more prominent in .45ACP wad cutters. I believe bullet shape and angle during chambering a round will affect set back and will also vary between guns. Well first you know I had trouble in the past with set back on 200gr SWC but I resolved that. My point is on properly taper crimped semi auto ammo set back shouldn't be a problem unless you are continually dropping the slide on the same round. Now , I believe it was Razo, posted a LEO senario. Well that I consider out of the ordinary and some form of mitigation must be used. I load and unload my bedside pistol about a dozen times a year. I don't like to drop the slide from locked open on a live round in the bedroom. So I ease it down. No set back. I understand what you're saying about SWC. In Ray's original post I envisioned him continually dropping the slide from lock open on the same round. But with service ammo (factory) A few slide drops shouldn't cause set back. If one slide drop causes set back the ammo is no good. Quote Share this post Link to post Share on other sites
Pizza Bob 1,488 Posted April 11, 2012 Setback was enough of a concern that Sig felt it necessary to issue a factory technical bulletin warning about this issue. Jim Flynn used to have it posted in his "lobby". Very real condition and one for major concern. JM (and Sig's) HO Adios, PIzza Bob Quote Share this post Link to post Share on other sites
raz-0 1,259 Posted April 11, 2012 Any mechanical device such as a bullet can be abused. I stand by my statement. Proper ammo will not set back under normal circumstances. If you are going to repetedly drop the slide on the same round inertia will have some effect. There are ways to aviod the bullet set back. It also depends on the gun and the caliber. For example .40 in a 1911 format gun tends to get jammed pretty well into the to of the chamber while making the adjustment in angle from magazine to bore. There are other deisgns where the angles amtch better and the magazine lips sit higher relative to the bore that are less abusive. Quote Share this post Link to post Share on other sites
BigHayden 77 Posted April 17, 2012 If you reload, just pack enough powder in the case so the bullet can't go in any further. That will solve the problem of set back. Warning: Don't just pack enough powder in the case so the bullet can't go in any further as this is dangerous and meant to be a joke. Though it would solve the bullet set back problem, if you pulled the trigger on a round setup like that, it would probably be the last thing you do before shuffling off your mortal coil. Now back to our actual post. Set back is a real problem (more pronounced for some calibers than others) and yes, there are ways to mitigate it. Riding the slide forward nice and easy is not the best answer though. The gun is designed to slam the slide forward repeatedly. Slowing it down with your hand has the potential to introduce problems, especially in a gun like the 1911, though likely not as must of a problem in a Glock. Set back happens every time you chamber a round under force, including when you are shooting. Most of the time it is an imperceptible amount and is not dangerous. Re-chambering the same same round over and over and over and over and (well, you get the point) will cause noticeable set back. The best way to mitigate set back is to rotate out the top round of your magazine if you load/unload your gun repeatedly. Once you've unloaded the same round, say twice, then you rotate it to the bottom of the magazine. Once it makes its way back to the top, then your only option, of course, is to shoot the entire magazine before loading up fresh ammo. Quote Share this post Link to post Share on other sites
RedBowTies88 41 Posted April 17, 2012 I've had enough of an issue with hornady 9x18 setting back that seriously makes me reconsider using it. In come cases half of what should be visible of the bullet had puched back... probably nearly 1/4" Quote Share this post Link to post Share on other sites
Socom 19 Posted April 17, 2012 shouldnt u know this by now Splash? Quote Share this post Link to post Share on other sites